Live manual

test @ sisudoc.org

sisu

[ document manifest ]

<< previous toc next >>

Live Systems Handbuch

Overview of tools

5. Overview of tools

This chapter contains an overview of the three main tools used in building live systems: live-build, live-boot and live-config.

5.1 The live-build package

live-build is a collection of scripts to build live systems. These scripts are also referred to as "commands".

The idea behind live-build is to be a framework that uses a configuration directory to completely automate and customize all aspects of building a Live image.

Many concepts are similar to those used to build Debian packages with debhelper:

Unlike debhelper, live-build provides the tools to generate a skeleton configuration directory. This could be considered to be similar to tools such as dh-make. For more information about these tools, read on, since the remainder of this section discuses the four most important commands. Note that the preceding lb is a generic wrapper for live-build commands.

5.1.1 The lb config command

As discussed in live-build, the scripts that make up live-build read their configuration with the source command from a single directory named config/. As constructing this directory by hand would be time-consuming and error-prone, the lb config command can be used to create the initial skeleton configuration tree.

The lb config command creates the following directories inside config/: hooks/, includes/, several other includes subdirectories for each stage of the build process and package-lists/. The latter includes a list of several important live packages like live-boot, live-config and live-config-sysvinit.

Issuing lb config without any arguments completes the config/ subdirectory which it populates with some default settings in configuration files, and two skeleton trees named auto/ and local/.

$ lb config
[2014-04-25 17:14:34] lb config
P: Updating config tree for a debian/wheezy/i386 system

Using lb config without any arguments would be suitable for users who need a very basic image, or who intend to provide a more complete configuration via auto/config later (see Managing a configuration for details).

Normally, you will want to specify some options. For example, to specify which package manager to use while building the image:

$ lb config --apt aptitude

It is possible to specify many options, such as:

$ lb config --binary-images netboot --bootappend-live "boot=live components hostname=live-host username=live-user" ...

A full list of options is available in the lb_config man page.

5.1.2 The lb build command

The lb build command reads in your configuration from the config/ directory. It then runs the lower level commands needed to build your Live system.

5.1.3 The lb clean command

It is the job of the lb clean command to remove various parts of a build so subsequent builds can start from a clean state. By default, chroot, binary and source stages are cleaned, but the cache is left intact. Also, individual stages can be cleaned. For example, if you have made changes that only affect the binary stage, use lb clean --binary prior to building a new binary. If your changes invalidate the bootstrap and/or package caches, e.g. changes to --mode, --architecture, or --bootstrap, you must use lb clean --purge. See the lb_clean man page for a full list of options.

5.2 The live-boot package

live-boot is a collection of scripts providing hooks for the initramfs-tools, used to generate an initramfs capable of booting live systems, such as those created by live-build. This includes the live system ISOs, netboot tarballs, and USB stick images.

At boot time it will look for read-only media containing a /live/ directory where a root filesystem (often a compressed filesystem image like squashfs) is stored. If found, it will create a writable environment, using aufs, for Debian like systems to boot from.

More information on initial ramfs in Debian can be found in the Debian Linux Kernel Handbook at ‹http://kernel-handbook.alioth.debian.org/› in the chapter on initramfs.

5.3 The live-config package

live-config consists of the scripts that run at boot time after live-boot to configure the live system automatically. It handles such tasks as setting the hostname, locales and timezone, creating the live user, inhibiting cron jobs and performing autologin of the live user.


[ document manifest ]

<< previous toc next >>